®
GARDENA
C1060 profi
Art. 1815
GB Operating Instructions
Water Computer Profi
S
Bruksanvisning
Bevattningscomputer
NL Gebruiksaanwijzing
Besproeiingscomputer
D
Gebrauchsanweisung
Bewässerungscomputer
FIN Käyttöohjeet
Kasteluohjain
3. Function
The battery must be exchanged in time to pre-
vent the Water Computer failing due to a low
battery when you are away for longer periods
of time. Make sure that the time the battery
has been in operation and the time you are
planning to be away does not add up to more
than a year.
does not affect the program in any way.
When the computer cools down the LCD
display illuminates again.
This GARDENA Water Computer C 1060 profi allows you
to water your garden completely automatically any time you
choose up to 6 times a day, whether you are using a sprinkler,
a sprinkler system installation or a drip-head watering system.
The max. temperature for the water flow is
40°C.
v Only use clear fresh water.
Your Water Computer waters your garden completely automati-
cally according to the program you choose. You can use your
Water Computer to water your garden early in the morning or
late at night when water evaporates the least or when you are
on holiday.
The minimum operating pressure is 0,5 bar,
the maximum operating pressure is 12 bar.
Setting up
Avoid tensile strain.
Warning! The Water Computer must not be
used indoors.
v Do not pull the hose connected to the
You simply program the watering start, watering time and watering
day(s) or cycles.
Water Computer.
v Only use the Water Computer outdoors.
The Water Computer may only be set up verti-
cally with the sleeve nut to the top to prevent
water penetrating into the battery compart-
ment.
Programming
v Program the Water Computer with the tap
Key-operated functions
Key
Key-operated function
turned off.
▲
Changes or moves on the input data. (If the
▲-key is held down, the figures change very
quickly.)
1
In this way you can avoid getting wet when
trying out the manual On/Off function (man.
On/Off). You can remove the control unit from
the housing to program the Water Computer.
The minimum water output to ensure that
the Water Computer functions correctly is
20- 30 l/h.
For example, at least 10 x 2-litre Drip Heads
are required to control the Micro-Drip-System.
O.K.
Menu
man.
On/Off
Confirms the values set with the ▲-key.
2
3
4
Changes to the next program level.
For switching the water throughput on or off
manually.
At high temperatures (over 60°C at the dis-
play) the LCD display may extinguish. This
4 1 2 3
4
5
Displays
Display
Description
Batt.
If the battery indicator begins to flash, the battery
is almost flat and watering programs will no longer
run. Any valves that are still open are closed again
even if the battery is almost flat.
F
G
Weekdays Current weekday or programmed watering days.
(Mo, Tu,...)
Prog.
special
5
6 9 0 A 7 C
F
G
Program selected (1 to 6).
6
7
The battery indicator is reset as soon as you
replace the battery with a new one.
Only for controlling the Automatic Water
Distributor Art.-No. 1198.
Prog.
Off
Watering program inactive
(Budget function: 0%)
time
Flashes when in input mode for the current data
(hours, minutes, day of the week).
8
9
0
A
START
PM
Flashes when in input mode for watering
start time.
The four display levels
Display levels
• Level 1:
• Level 2:
• Level 3:
• Level 4:
Normal display
Enter the current time and day of the week
Insert watering programs
D
5 8 E
B
Display for 12-h-clock
(e. g. in USA, Canada).
(Time/
Current time / Watering start time
% Run-Time / Prog. Off
Start time) (display 13 h = 1 pm; e. g. in USA, Canada).
RUN Time
3rd, 2nd
can be selected one after the other by pressing the Menu-key.
Watering time (flashes when in input mode).
B
C
Watering cycles
You can change display level at any time, even during program-
ming. All the program data which have been confirmed up to
that point with the O.K.-key are stored.
(3rd every 3rd day / 2nd every 2nd day).
% Run-
Time
Budget function: the watering time of all watering
programs can be reduced centrally in intervals of
10% from 100% to 0%.
D
E
ERROR
Error message for the special function
if watering programs overlap.
6
7
Connect Water Computer:
The Water Computer is fitted with a sleeve nut
for taps with
allows the
L
4. Putting Your Water Computer into Operation
G1” (33.3 mm) thread. The adaptor supplied
K
Water Computer to be connected to taps with a G 3/4” thread
(26.5 mm).
This Water Computer must only be powered by a 9V alkaline
manganese (alkaline) battery type IEC 6LR61.
Insert battery:
K
L
Connect Water Computer to water tap with G1” (33.3 mm)
thread:
1. Press unlock button and pull control
H
unit
out of the Water Computer housing.
I
I
1. Screw sleeve nut
of the Water Computer on to the tap
L
2. Insert battery
compartment.
into battery
J
thread by hand (do not use pliers).
2. Screw tap connector on to the Water Computer.
M
Ensure that the battery polarity P is
correct.
The display shows all the LCD-symbols
for 2 seconds and then moves to the
time/day of week level.
H
Connect Water Computer to tap with G 3/4” (26.5 mm) thread:
1. Screw adaptor on to the tap manually (do not use pliers).
K
2. Screw sleeve nut
of the Water Computer on to the adaptor
L
thread
by hand (do not use pliers).
K
3. Re-insert control unit
in housing.
I
D
z
M
3. Screw tap connector
on to the Water Computer.
M
Programming aid:
v Stick the self-adhesive programming
aid on the inside of the display cover D .
The display cover can be folded up to protect the display against
the weather.
Before you start entering the watering data in the computer
we recommend that you write the data on one of the watering
plans in the appendix to maintain more of an overview.
Compile watering plan:
P
z
J
8
9
Example:
Fit anti-theft device
(optional):
To secure your Water Computer against theft, you can obtain
the GARDENA anti-theft device art. no. 1815-00.791.00 from
GARDENA Service.
Program
Starting time
Watering time
Watering days / Watering cycles
Mo Tu We Th Fr Sa So 2nd 3rd
PROG
START TIME
RUN TIME
1. Screw clamp
Computer.
with screw
firmly to the back of the Water
O
P
P
1
2
3
4
5
6
7:30
19:00
22:30
4:00
–
0:30
0:20
1:10
0:15
–
X
X
X
2. Use clamp e.g. for fixing a chain.
X
X
It is no longer possible to remove the screw after it has been
screwed in.
X
X
X
X
O
–
–
5. Programming
Connect soil moisture
or rain sensor (optional):
In addition to time-based watering, it is also possible to include
the soil moisture or rain sensor in the watering programs.
The control unit
can be removed from the housing for pro-
I
gramming by pressing the unlock button
can be undertaken whilst you are moving around (see 4.
Putting Your Water Computer into Operation “Insert battery” ).
and programming
H
If the soil is moist enough, the program will be stopped, or a
program will be prevented from starting. Manual operation via
man. On/Off is unaffected by this.
Set current time
and day of week:
N
1. Place soil moisture sensor in the watered area
– or –
1. Press Menu-key (not necessary if the battery has just been
place rain sensor (with extension cable if necessary)
outside the watered area.
inserted).
2. Insert the sensor in the sensor connection
Computer.
of the Water
The hours display and time flash.
N
1.
10
11
2. Set the time in hours with the ▲-key
1. Press Menu-key twice
(example: 9 hours) and confirm with the O.K.-key.
(not necessary if the current time and day of the week
has been entered).
time and the minutes display flash.
Program memory setting 1 flashes.
2.
3.
1.
2.
3.
4.
3. Set the time in minutes with the ▲-key
2. Only if the Automatic Water Distributor is used:
(example: 30 minutes) and confirm with the O.K.-key.
Select special-function with the ▲-key and confirm with
the O.K.-key (continue with step 4).
time and the day of the week display flash.
Program memory setting 1 is selected automatically,
start time and the hours section flash on the display.
4. Set the day of the week with the ▲-key
(example: ■ Sa Saturday) and confirm with the O.K.-key.
3. Select program memory setting with the ▲-key
(example: Prog. 3 ■ program 3) and confirm with the
O.K.-key.
The display moves to the message Insert watering programs
and program memory setting 1 flashes.
4.
start time and the hours section flash on the display.
Enter watering programs:
You must reset your Water Computer before selecting the
special function (see 6. Automatic Water Distributor).
4. Set the hours for starting the watering time with the ▲-key
(example: 6 hours) and confirm with the O.K.-key.
v Reset: Keep ▲-key and O.K.-key pressed simultaneous
for 2 seconds.
start time and the minutes section flash on the display.
Up to 6 watering programs can be inserted – or –
the special function can be selected.
12
13
5. Set the minutes for starting the watering time with the ▲-key
(example: 20 minutes) and confirm with the O.K.-key.
8. (b) Select respective watering days with the ▲-key
(example: ■ Mo, ■ Fr Monday and Friday) and confirm
with the O.K.-key. Press ▲-key until the ■ over Su
disappears.
RUN TIME and the hours for the watering time flash on the
display.
The display returns to step 3 and the next highest program
memory setting flashes.
5.
6.
7.
8. (b)
6. Set the hours for the watering time with the ▲-key
(example: 0 hours) and confirm with the O.K.-key.
V
If you would like to water your garden every day, press
the OK button to confirm each day one after another.
RUN TIME and minutes for the watering time flash on the
display.
When the program has been created for program memory setting 6,
the display moves to the message % Run-Time / Prog. Off.
Activate watering programs:
You must select the Run-Time percentage you wish to activate
before the watering programs can run.
7. Set watering time minutes with the ▲-key
(example: 10 minutes) and confirm with the O.K.-key.
9. Press Menu-key 3 times (not necessary if the program has
just been compiled for program memory setting 6).
Watering cycle ■ 3rd flashes on the display.
10. Select the percentage (see Budget Function) for the pro-
grammed watering time using the ▲ key (e.g. 60 % Run-Time)
and then confirm your selection by pressing the O.K. key.
The display moves to the normal display.
8. (a) Select watering cycle with the ▲-key (example: ■ 2nd
and confirm with the O.K.-key
)
10.
(2nd /3rd: watering every 2nd day / 3rd day).
Programming the Water Computer has now been completed,
i.e. the built-in valve opens/closes entirely automatically and
thus undertakes watering at the programmed times.
The display returns to step 3 and the next highest
program memory setting flashes.
8 (a)
– or –
14
15
Programmed watering time
Budget-Function (%Run-Time):
1. Press man. On/Off-key to open the valve manually
(or to close an open valve).
RUN TIME and the watering time in minutes (set to 30 minutes
in the works) flash for 5 seconds on the display.
The times of all stored watering programmes can be reduced cen-
trally in intervals of 10%, from 100% down to 10%, without having
to change each interval programme. This is ideal if you wish to
water your garden less in the Autumn than in the Summer.
1.
2.
2. Whilst the watering time in minutes is flashing, the watering
:
duration can be modified with the ▲-key (between 0 00
10 - 100 % Run-Time = Watering program active
:
and 0 59) (example: 10 minutes).
Watering program deactivated
0
Prog. Off
= Watering program inactive
The valve is opened.
3. Press man. On/Off-key to close the valve early.
Note: If you change the watering time percentage, your Water
Computer will still display the watering time you originally pro-
grammed for the individual watering programs.
The valve is closed.
The amended manual opening period is stored, i.e. each time
the valve is opened manually in future the modified opening
period is preset. If the manual opening period is amended to
Read/ modify
watering programs:
If a program has already been set on one of the 6 program
memory settings, this can be modified without having to compile
it from the beginning again.
:
0 00, the valve is closed and also remains closed after the
man. On/Off-key is pressed (child lock).
1. Press Menu-key twice.
Program memory setting 1 flashes.
If the valve has been opened manually and a programmed start
of a watering period overlaps the manual opening period, the
programmed starting time is suppressed.
2. Press O.K.-key to move to the next program step – or –
modify program data with the ▲-key and confirm with the
O.K.-key.
Example: The valve is opened at 9.00 a.m. manually, the
opening period is 30 minutes. A program with a start time
(START TIME) between 9.00 and 9.30 a.m. will not be under-
taken in this case.
Manual operation:
The valve can be opened or closed manually at any time.
A program-controlled open valve can also be closed early with-
out changing the program data (start time, watering duration
and watering days).
16
17
Reset
The factory settings are restored.
6. Automatic Water Distributor (optional)
v Press ▲-key and O.K.-key simultaneously for 2 seconds.
Connecting the GARDENA Automatic Water Distributor
(Art. No. 1198) allows you to control up to 6 watering lines with
the Water Computer C 1060 profi.
Each of the 6 watering lines can only be actuated once a day.
This is ideal where there is an insufficient amount of water or
where individual areas of the garden have varying water require-
ments. It allows all watering lines to be operated one after
another.
Using the special function, your Water Computer C 1060 profi is
able to take into account the special requirements of the Automatic
Water Distributor, when programming.
Function
All the LCD symbols are displayed for 2 seconds and the
display moves to the normal display.
• All the program data are set to zero.
• The manual watering period is set to 0 30 again.
:
• The time and day of the week are retained.
Important notes:
If no entry is made during programming for a period of more
than 60 seconds, the normal display reappears.
Programming
With overlapping programs and identical watering days, the
1st watering starting time has priority and other programs are
not initiated.
Special function
If program data have already been inserted beforehand, a RESET
must be undertaken before the special function can be set.
v Keep ▲-key and O.K.-key pressed simultaneously for
Example:
2 seconds.
To ensure the Automatic Water Distributor switches safely there
must be at least a 30 minute break between the programs entered
in the Water Computer.
When you have confirmed the special function with O.K. and
have entered the data for the first program (see 5. Programming)
all the programmes which follow will be pre-programmed auto-
matically.
Program
Starting time
Watering time
Watering days / Watering cycles
Mo Tu We Th Fr Sa So 2nd 3rd
PROG
START TIME
4:00
RUN TIME
1
0:40
1:00
X
X
X
2
4:30
The first program is run on Monday, the 2nd program is cancelled.
18
19
The pre-programming takes into consideration the 30 minute
break required between the programs as well as a minimum
watering time of 30 seconds (display: 1 min.).
This watering time is required to allow the Automatic Water
Distributor to switch to the next outlet and to ensure that the
order of the watering programs to the appropriate watering
line is retained.
By briefly opening the water flow the outlets on the Automatic
Water Distributor are switched further so that when the watering
programs are reactivated (% Run-Time) the original order of the
outlets for the required watering program is retained.
Soil Moisture Sensor /
Rain Sensor
When using the Water Computer C 1060 prof together
with the Automatic Water Distributor, Soil Moisture Sensor
(Art. No. 1187) or Rain Sensor electronic (Art. No. 1189)
please note the following:
The watering days entered for the watering program are valid
for all other watering programs.
If the special function is activated and the Soil Moisture or
Rain Sensor indicates sufficient moisture, watering is interrupted.
The watering time of following watering programs is shortened
to 30 seconds (display: 1 min.) until the Soil Moisture / Rain
Sensor allows the watering programs to be resumed. The water-
ing time originally entered then begins.
Error message (ERROR)
You can alter the watering starting times and watering times
pre-programmed by the Water Computer to meet your personal
requirements. However, if you do not take into account the break
times mentioned above, any changes you make are not accepted
and an error message appears on the display (ERROR).
Since it is very easy for watering times to overlap slightly, espe-
cially when the beginnings and ends of programs are very close
together, it is sensible to RESET the Water Computer and to
re-enter the watering data to prevent an error message appearing.
Shortening the watering time when the soil is sufficiently moist
ensures that the automatic water distributor is switched to the
next outlet and therefore ensures that the correct order of the
watering program for the respective distributor outlet is retained.
On/Off Prog.
If the watering programs are switched off after you have con-
firmed the special function (status indicator on Off Prog.) all the
programs which begin in this time are shortened to the minimum
watering time of 30 seconds (display: 1 min.) This ensures that
the order of the watering programs to the appropriate outlet of
the Automatic Water Distributor is retained.
20
21
Fault
Possible Cause
Remedy
7. Cleaning
No display appears
Temperature on the display
is higher than 60°C.
Display appears after
temperature has dropped.
v Check function by operating
manually. (man. On/Off).
The filter should be checked regularly and cleaned when
necessary.
Clean filter:
1. Unscrew sleeve nut
of the Water Computer by hand
L
L
from the tap thread (do not use pliers).
Programs cannot be
entered
The current time and the day
of the week were not entered
completely.
v Enter time and day of week
(see 5. Programming).
2. Remove filter from sleeve nut and clean.
L
3. Screw sleeve nut
of the Water Computer back on to the
L
thread of the tap by hand (do not use pliers).
Manual opening via the
man. On/Off-key is not
possible
Low battery power, Batt.
indicator flashes
v Insert new (alkaline) battery
Manual watering period is set
v Set manual watering period
:
to 0 00.
to a figure greater than
:
0 00 (see 5. Programming).
Tap turned off.
v Turn tap on.
8. Trouble-Shooting
Watering program is not
being undertaken
(no watering)
Watering program has not
been entered completely.
v Read off watering program
and modify if necessary.
Fault
Possible Cause
Remedy
Programs deactivated
v Activate program
(Prog. Off).
(% Run-Time).
No display appears
Battery inserted incorrectly.
v Check polarity markings
match (+/–).
Program entry/modification
during or just before the
start pulse.
v Make program entry/
modification outside the
programmed start times.
Flat battery.
v Insert new (alkaline) battery.
v Check function by operating
manually (man. On/Off).
22
23
Fault
Possible Cause
Remedy
9. Putting Your Water Computer out of Operation
Watering program is not
being undertaken
(no watering)
Valve was opened manually
previously.
v Avoid possible program
overlaps.
1. Press Menu-key 3 times, select Prog. Off with the ▲-key
Over-wintering /
storage:
and confirm with the O.K.-key.
Tap turned off.
v Turn on tap.
The watering programs are deleted.
Program overlap
(1st watering start time has
priority).
v Enter new watering
2. Store your Water Computer in a dry place where it is protected
from frost.
program without overlaps.
Please return flat batteries to a GARDENA dealer or dispose
of them properly at your nearest recycling centre. Only dispose
of batteries when they are flat.
Soil moisture or rain sensor
reports sufficient moisture.
v If dry, check setting/
location of soil moisture/
rain sensor.
Batt. indicator flashes because
battery is almost flat.
v Insert new (alkaline) battery
10. Accessories
Water Computer does
not close
Minimum quantity of water
drawn is less than 20 l/h.
v Connect more drip heads
Automatic control with:
GARDENA Soil Moisture Sensor
GARDENA Rain Sensor electronic
GARDENA Automatic Water Distributor
Art. No. 1187
Art. No. 1189
Art. No. 1198
If you have any other problems with your Water Computer, please contact GARDENA Service.
24
25
11. Technical Data
12. Service
Warranty
Min. /max. operating pressure:
Flow medium:
0,5 bar / 12 bar
Clear fresh water
40°C
GARDENA guarantees this product for 2 years (from date of
purchase). This guarantee covers all serious defects of the unit
that can be proved to be material or manufacturing faults.
Max. medium temperature:
Under warranty we will either replace the unit or repair it free
of charge if the following conditions apply:
Number of program-controlled
watering cycles per day:
Up to 6
• The unit must have been handled properly and in keeping
with the requirements of the operating instructions.
Watering duration per program:
Battery required:
1 min. to 9 hours 59 min.
• Neither the purchaser or a non-authorised third party have
attempted to repair the unit.
1 × 9V alkaline manganese (alkaline) battery
type IEC 6LR61
Damage caused by frost is not covered by the warranty.
Operating time of the battery
approx. 1 year
This manufacturer’s guarantee does not affect the user’s existing
warranty claims against the dealer/seller.
If you have any problems with your Water Computer, please
contact our Customer Service or return the defective unit to-
gether with a short description of the problem directly to one of
the GARDENA Service Centres listed on the back of this leaflet.
26
27
Product Liability
Product Liability
G
f
We expressly point out that, in accordance with the product liability law, we are not liable for any damage
caused by our units if it is due to improper repair or if parts exchanged are not original GARDENA parts
or parts approved by us, and, if the repairs were not carried out by a GARDENA Service Centre or an
authorised specialist. The same applies to spare parts and accessories.
Painotamme tuotevastuulain mukaisesti erityisesti sitä seikkaa, että emme vastaa elektroniselle vesiajas-
timelle aiheutuneista tai sen aiheuttamasta vahingoista, mikäli ne ovat aiheutuneet epäpätevän korjauksen
takia, mikäli elektroniseen vesiajastimeen on vaihdettu osia, jotka eivät ole alkuperäisiä GARDENA-osia tai
meidän hyväksymiä osia tai mikäli korjauksen on tehnyt jokin muu kuin GARDENA-huolto tai valtuutettu
huolto. Sama koskee myös lisälaitteita ja -varusteita.
Produktansvar
S
N
Tillverkaren är inte ansvarig för skada som orsakats av produkten om skadan beror på att produkten har
reparerats felaktigt eller om, vid reparation eller utbyte, andra än Original GARDENA reservdelar har an-
vänts. Samma sak gäller för kompletteringsdelar och tillbehör.
EU Certificate of Conformity
The undersigned GARDENA International GmbH, Hans-Lorenser-Str. 40, D-89079 Ulm, hereby certifies that, when leaving
our factory, the unit indicated below is in accordance with the harmonised EU guidelines, EU standards of safety and product
specific standards. This certificate becomes void if the unit is modified without our approval.
G
S
N
Productaansprakelijkheid
Wij wijzen er nadrukkelijk op, dat wij op grond van de wet aansprakelijkheid voor producten niet aanspra-
kelijk zijn voor schade ontstaan door onze apparaten, indien deze door onvakkundige reparatie veroorzaakt
zijn, of er bij het uitwisselen van onderdelen geen gebruik gemaakt werd van onze originele GARDENA
onderdelen of door ons vrijgegeven onderdelen en de reparatie niet door de GARDENA technische dienst
of de bevoegde vakman uitgevoerd werd. Ditzelfde geldt voor extra-onderdelen en accessoires.
EU Tillverkarintyg
Undertecknad firma GARDENA International GmbH, Hans-Lorenser-Str. 40, D-89079 Ulm, intygar härmed att nedan nämnda
produkter överensstämmer med EU:s direktiv, EU:s säkerhetsstandard och produktspecifikation. Detta intyg upphör att gälla
om produkten ändras utan vårt tillstånd.
Produkthaftung
D
EU-overeenstemmingsverklaring
Wir weisen ausdrücklich darauf hin, dass wir nach dem Produkthaftungsgesetz nicht für durch unsere
Geräte hervorgerufene Schäden einzustehen haben, sofern diese durch unsachgemäße Reparatur verur-
sacht oder bei einem Teileaustausch nicht unsere Original GARDENA Teile oder von uns freigegebene
Teile verwendet werden und die Reparatur nicht vom GARDENA Service oder dem autorisierten Fachmann
durchgeführt wird. Entsprechendes gilt für Ergänzungsteile und Zubehör.
Ondergetekende GARDENA International GmbH, Hans-Lorenser-Str. 40, D-89079 Ulm, bevestigt, dat het volgende ge-
noemde apparaat in de door ons in de handel gebrachte uitvoering voldoet aan de eis van, en in overeenstemming is met
de EU-richtlijnen, de EU-veiligheidsstandaard en de voor het product specifieke standaard. Bij een niet met ons afgestemde
verandering aan het apparaat verliest deze verklaring haar geldigheid.
EU-Konformitätserklärung MaschinenVerordnung (9. GSGVO) / EMVG / Niedersp. RL
D
Der Unterzeichnete GARDENA International GmbH, Hans-Lorenser-Str. 40, D-89079 Ulm, bestätigt, dass das nach-
folgend bezeichnete Gerät in der von uns in Verkehr gebrachten Ausführung die Anforderungen der harmonisierten
EU-Richtlinien, EU-Sicherheitsstandards und produktspezifischen Standards erfüllt. Bei einer nicht mit uns abgestimmten
Änderung des Gerätes verliert diese Erklärung ihre Gültigkeit.
134
135
PROG
START TIME
RUN TIME
Mo Tu We Th Fr Sa So 2nd 3rd
EU-Vakuustodistus
f
Allekirjoittanut, GARDENA International GmbH, Hans-Lorenser-Str. 40, D-89079 Ulm, vahvistaa, että lähtiessään tehtaalta ko.
tuote (tuotteet) on valmistettu EU-ohjeiden, EU-turvallisuus – ja tuote-erittelystandardien mukaisesti. Tämä vakuus mitätöityy,
mikäli tuotetta (tuotteita) muutetaan ilman hyväksyntäämme.
1
2
3
4
5
6
Description of the unit:
Produktbeskrivning:
Omschrijving van het apparaat:
Bezeichnung des Gerätes:
EU-direktiivit:
Water Computer
Type:
Type:
Typ:
Typ :
Tyyppi:
Art. No.:
Art.nr. :
Art. nr.:
Art.-Nr.:
art.-nro
Bevattningscomputer
Besproeiingscomputer
Bewässerungscomputer
Kasteluohjain
C 1060
profi
1815
1998
EU directives:
EU direktiv:
EU-richtlijnen:
EU-Richtlinien:
EU-direktiivit:
Year of CE marking:
CE-Märkningsår:
Installatiejaar van de CE-aanduiding:
Anbringungsjahr der CE-Kennzeichnung:
CE-hyväksyntä vuosi:
89/336/EC
93/68/EC
PROG
START TIME
RUN TIME
Mo Tu We Th Fr Sa So 2nd 3rd
1
2
3
4
5
6
Thomas Heinl
Ulm, 17.07.1998
Ulm, 1998.07.17.
Ulm, 17-07-1998
Ulm, 17.07.1998
Ulm, 17.07.1998
Technical Dept. Manager
Technical Director
Hoofd technische dienst
Technische Leitung
Tekn. osaston päällikkö
136
Deutschland
Brazil
RGS Comercial Ltda
Av. Marginal do
Rio Pinheiros, 5200
Edificio Montreal
Bloco e -Térreo
Cyprus
Great Britain
Italy
New Zealand
NYLEX New Zealand Limited
Private Bag 94001
South Auckland Mail Centre
10 Offenhauser Drive
East Tamaki, Manukau
GARDENA
FARMOKIPIKI LTD
P.O. Box 7098
74, Digeni Akrita Ave.
1641 Nicosia
GARDENA UK Ltd.
27-28 Brenkley Way
Blezard Business Park
Seaton Burn
GARDENA Italia S.p.A.
Via Donizetti 22
20020 Lainate (Mi)
International GmbH
Service Center
Hans-Lorenser-Straße 40
D-89079 Ulm
Produktfragen: (0731) 490-246
Reparaturen: (0731) 490-290
Japan
Newcastle upon Tyne NE13 6DS
Czech Republic
GARDENA spol. s.r.o.
Шнpskб 20a, и.p. 1153
62700 Brno
KAKUDAI Mfg. Co. Ltd.
1-4-4, Itachibori Nishi-ku
Osaka 550
05693-000 Sao Paulo - SP
Greece
Agrokip
G. Psomadopoulos & Co.
33 A, Ifestou str. – 194 00
Industrial Area Koropi
Athens
Norway
Bulgaria
GARDENA Norge A/S
Postboks 214
2013 Skjetten
Argentina
Argensem S.A.
Calle Colonia Japonesa s/n
(1625) Loma Verde
Buenos Aires
DENEX LTD.
2 Luis Ahalier Str.
7th floor
Luxembourg
Magasins Jules Neuberg
Grand Rue 30
Case Postale No. 12
Luxembourg 2010
Denmark
GARDENA Danmark A/S
Naverland 8
Poland
Sofia 1404
GARDENA Polska Sp. z o.o.
Szymanóv 9 d
Canada
2600 Glostrup
Hungary
Australia
GARDENA Canada Ltd.
100 Summerlea Road
Brampton, Ontario
Canada L6T 4X3
GARDENA Magyarország Kft.
Késmárk utca 22
1158 Budapest
05-532 Baniocha
Finland
Habitec Oy
Martinkyläntie 52
01720 Vantaa
Netherlands
NYLEX Consumer Division
76-88 Mills Road
P.O. Box 722
GARDENA Nederland B.V.
Postbus 50176
Portugal
GARDENA Portugal Lda.
Recta da Granja do Marquês
Edif. GARDENA
Iceland
Heimilistaeki hf
Saetun 8
P.O. Box 5340
125 Reykjavik
1305 AD ALMERE
Braeside 3195
Melbourne, Victoria
Chile
France
Neth. Antilles
Antonio Martinic Y CIA. LTDA.
Gilberto Fuenzalida 185 Loc.
Las Condes
Algueirão
2725-596 Mem Martins
GARDENA France
Service Après-Vente
BP 50080
Jonka Enterprises N.V.
Sta. Rosa Weg 196
P.O. Box 8200
Austria
GARDENA Österreich
Ges. m.b.H.
Stettnerweg 11-15
2100 Korneuburg
Russia / Россия
АО АМИДА ТТЦ
ул. Моcфилмовcкая 66
117330 Моcква
Santiago de Chile
95948 ROISSY CDG Cedex
Republic of Ireland
Michael McLoughlin & Sons
Hardware Limited
Long Mile Road
Curaçao
Costa Rica
Compania Exim
Euroiberoamericana S.A.
Av. 12 bis Calle 16 y 18
Bodegas Keith y Ramirez
San José
Belgium
MARKT (Belgium) NV/SA
Sterrebeekstraat 163
1930 Zaventem
Dublin 12
Singapore
Spain
Ukraine / Украина
АОЗТ АЛЬЦЕСТ
ул. Гайдара 50
г. Киев 01033
Hy - Ray Enterprises
Block 1002 Toa Payoh
Industrial Park
GARDENA IBÉRICA S.L.U.
C/ Basauri, nº 6
La Florida
#07-1433/1435/1451
Singapore 319074
28023 Madrid
Turkey
Sweden
GARDENA/Dost Diþ Ticaret
Mümessillik A.Þ.
Yeþilbaðlar Mah. Baþkent
Cad. No. 26
Slowenia / Croatia
Silk d.o.o. Trgovina
Brodiљиe 15
GARDENA Norden AB
Box 9003
20039 Malmö
1236 Trzin
Pendik - Ýstanbul
Switzerland
GARDENA AG
Bitziberg 1
South Africa
GARDENA
South Africa (Pty.) Ltd.
P.O. Box 11534
Vorna Valley 1686
USA
GARDENA
3085 Shawnee Drive
Winchester, VA 22604
8184 Bachenbülach
1815-28.960.04/0041
GARDENA Manufacturing GmbH
D-89070 Ulm
©
http://www.gardena.com
|