ZIC360NR – GE Monogram 36" Built-In Bottom Freezer Refrigerator
with Automatic Icemaker
The Installation Space
Door Swing Clearances
The finished cutout width must be 35-1/2".
The installation must allow for clearances to adjacent walls or cabinets.
These refrigerators are equipped with a 2-position door stop. The
factory-set 130° door swing can be adjusted to 90° if clearance to
adjacent cabinets or walls is restricted.
35-1/2"
Finished Width
Wall View
2-5/16"
10"
25"
Min. to
Wall
23-7/8"
Behind
Frame
6"
90° Door Swing
130° Door Swing
Electrical
Area
75" From
Floor to Bottom
of Electrical
Area
84-1/2" max
83-1/2" min
Finished
24" Cutout Depth
5"
36-3/4"
Opening
5"
Water Supply
3 1/2"
90°
130°
3 1/2"
4" Min.
to Wall
The cutout depth must be 24"
The refrigerator will project forward, slightly beyond adjacent cabinetry,
depending on your installation.
The cutout depth beneath a soffit
When installed beneath a soffit, the soffit cannot exceed the 24"
installation depth shown. The top case trim overlaps the bottom
of the soffit.
Allow 25" minimum clearances for a full 130° door swing. Allow 15"
for pan removal.
• 4" minimum clearance is required when the door swing is adjusted to
90°. If the 90° door stop position is used, pan access is maintained,
but pan removal is restricted.
• See door swing illustrations to determine interaction with adjacent
cabinets or countertops.
Electrical
A 115V, 60Hz., 15 or 20 amp power supply is required. An individual
properly grounded branch circuit or circuit breaker is recommended.
Install a properly grounded 3-prong electrical receptacle recessed
into the back wall. Electrical must be located on rear wall as shown.
ZUG2, ZUGSS2 Unified Grille Panel Kit
• If you are installing two refrigerators side by side, the installation space
must be 71-1/2" wide.
Note: GFI (ground fault interrupter) is not recommended.
Water Line
All models are equipped with an automatic icemaker. The water line can
enter the opening through the floor or back wall. Route GE SmartConnect™
Kit or 1/4" O.D. copper tubing between the cold water line and the water
connection location at the front of the refrigerator. The installation of an
easily accessible shut-off valve in the water line is required.
Note: Additional cutout width may be required when side panels are
used. Add side panel thickness to the finished cutout to calculate
rough-in width.
• The water and electrical locations for each product must be located
as shown.
• A separate 115V, 60Hz., 15 or 20 amp power supply is recommended for
each product.
Product Dimensions
71-1/2" Finished Width
35"
Case Width
Case Depth:
25-3/8" Framed Models
25-3/4" Stainless Steel Models
2-5/16"
Wall View
Electrical
24-3/16"
6"
*Shipping Height. The
refrigerator can be
10"
10"
*84" From
Floor to
adjusted to fit into a
cutout that is 83-1/2" min.
to 84-1/2" max. height.
The top case trim at the
front is 1/2" higher and
will overlap upper
84-1/2" max
83-1/2" min
Finished
24" Cutout
Depth
75" From
Floor to Bottom
of Electrical
Area
*83-1/2"
at
Top Frame
Rear
Opening
5"
5"
Water Supply
26"
Water Supply
26"
cabinetry or soffit.
3-1/2"
3-1/2"
36"
Frame to Frame Width
Use leveling legs and
wheels for a maximum
1" height adjustment.
®
For answers to your Monogram, GE Profile™ or
GE appliance questions, visit our website at
GEAppliances.com or call
Depth Including Handles:
26-7/8" Framed Models
Listed by
Underwriters
Laboratories
27-3/4" Stainless Steel Models
R
Specification Created 5/04
GE Answer Center® service, 800.626.2000.
110100
ZIC360NR – GE Monogram 36" Built-In Bottom Freezer Refrigerator
with Automatic Icemaker
1/4" Framed Panel Dimensions
3/4" Overlay Panel Dimensions
If you choose to install framed panels,
they must be cut to the dimensions
shown. The panels will slide into the
frame on the door, drawer and grille.
For a more custom appearance, overlay
panels may be installed on trimmed
models. The overlay panel must be
secured to a 1/4"-thick backer panel
which slides into the trim. A spacer
panel 0.10" thick must be placed
5/16"
Trim
Door/Drawer
Door/Drawer
Reveal
Overlay
Panel
If the custom panel is less than 1/4"
thick, and it fits loosely in the door
frame, it can be backed up with a
piece of filler material or foam tape
to improve the fit.
1/4"
Panel
between the overlay and backer panel.
Important Note: Maximum weight for
fresh food panel is 50 pounds,
30 pounds for freezer drawer panel
and 11 pounds for the grille panel.
1/4"
Backer
Panel
.10"
Spacer
.250" + .10" + .750" =
1.100" Total Panel Thickness
Center each panel over
the other. Assemble the
panels with glue and
screws. Screws must
be countersunk into the
backer panel.
Overlay Panel
A
Grille Panel
B
C
Spacer Panel
Backer Panel
Fresh Food
Panel
NOTE: Left-to-right offset is not always equal to top-to-bottom offset.
ZUG2 Grille Panel Dimensions
The ZUG2 Unified Grille Panel Kit will accept a framed or overlay
grille panel.
Freezer Drawer
Panel
D
• Assemble the overlay panel in the same manner as the door and
drawer panels.
Framed Panel Dimensions (in inches)
A (Width) B (Grille Ht.) C (FF Ht.) D (FZ Ht.)
1/4" Framed Panel 33-7/8 8-7/8 46-1/16 21-7/8
A
B
Grille Panel
3/4" Overlay Panel Dimensions (in inches)
A (Width) B (Grille Ht.) C (FF Ht.) D (FZ Ht.)
Framed Panel Dimensions
1/4" Backer Panel 33-7/8
.10" Spacer Panel 32-1/2
3/4" Overlay Panel 34-1/8
8-7/8
7-5/8
9
46-1/16
44-11/16
46-5/16
21-7/8
20-1/2
22
A (Width)
B (Height)
8-7/8"
1/4" Framed Panel
69-7/8"
Overlay Panel Dimensions
A (Width)
B (Height)
8-7/8"
7-5/8"
9"
1/4" Backer Panel
.10" Spacer Panel
3/4" Overlay Panel
69-7/8"
68-1/2"
70-1/8"
For answers to your Monogram, GE Profile™ or
GE appliance questions, visit our website at
GEAppliances.com or call
®
Listed by
Underwriters
Laboratories
R
Specification Created 5/04
GE Answer Center® service, 800.626.2000.
110100
ZIC360NM – GE Monogram 36" Built-In Bottom Freezer Refrigerator
with Automatic Icemaker
Advance Planning for Built-In Custom Bottom-Freezer Refrigerators
Use this page to determine door
swing interaction with adjacent
cabinets or countertops.
Frameless Cabinets: The case trim overlaps cabinets at the top and sides.
Therefore, frameless cabinets may require filler strips to prevent interference
with cabinet door swing. The opening must allow for filler strips.
Refrigerator
23-7/8" From
Rear of
Refrigerator
1"
2"
3"
Case
Trim
3/4"
1-3/4"
1-1/2"
1-1/4"
2-3/4"
2-1/2"
2-1/4"
1/2"
1/4"
1/4"
1/2"
3/4"
1"
3/4" Overlay
Panel
(Nominal Size)
Door
1/4"
Top View
1/2"
3/4"
130° Door Swing
(Optional setting)
Scale 1:1
1"
1-1/4"
Listed by
Underwriters
Laboratories
R
®
For answers to your Monogram, GE Profile™ or
GE appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center® service, 800.626.2000.
Specification Created 5/04
110100
ZIC360NM – GE Monogram 36" Built-In Bottom Freezer Refrigerator
with Automatic Icemaker
Advance Planning for Built-In Custom Bottom-Freezer Refrigerators
Use this page to determine door
swing interaction with adjacent
cabinets or countertops.
Refrigerator
Case Trim
23-7/8"
From Rear of
Refrigerator
Frameless Cabinets: The case trim
overlaps cabinets at the top and sides.
Therefore, frameless cabinets may require
filler strips to prevent interference with
cabinet door swing. The opening must
allow for filler strips.
1/4"
1/2"
3/4"
1"
1-1/4"
1-1/2"
Top View
90° Door Swing
(Optional setting)
Scale 1:1
Door
3/4" Overlay
Panel
(Nominal Size)
1/4"
Listed by
Underwriters
Laboratories
R
1/2"
®
For answers to your Monogram, GE Profile™ or
GE appliance questions, visit our website at
GEAppliances.com or call
3/4"
1"
GE Answer Center® service, 800.626.2000.
Specification Created 5/04
110100
1-1/4"
ZIC360NR – GE Monogram 36" Built-In Bottom Freezer Refrigerator
with Automatic Icemaker
Features and Benefits
• 20.6 Cu. Ft. Capacity
• Upfront electronic controls with digital readout
• Multi-shelf air management tower
• 2 Sealed, adjustable humidity vegetable/fruit pans with
easy access lids and full extension slides
• 2 Sealed deli pans with full extension slides
• Adjustable spillproof glass cabinet shelves
• Slide-out freezer compartment with full
extension slides
• Model ZIC360NRRH – Right-handed door swing
(Door panels required)
• Model ZIC360NRLH – Left-handed door swing
(Door panels required)
Specification Created 5/04
110100
|