All about the
Use&Care
of your
Room Air Conditioner
TABLE OF CONTENTS
Important Safety Instructions
Product Registration
Packaging
2-3
4
Operating Instructions
Care and Cleaning
5-9
9
Energy Saving Ideas
Before ou Call
4
10
11
Normal Sounds
4
ir Conditioner Features
5
Major Applia
www.frigidaire.com UA -800-944-9044
Important Safety Instructions
SAFETY PRECAUTIONS
CAUTION! Avoid Injury or damage to the unit or other property
Provide occasional ventilation during use. Do not direct airflow at fireplaces or other heat related sources as this could cause flare ups or make
units run excessively.
Do not climb on or place objects on outdoor part of the unit.
Do not hang objects off the unit.
Do not place containers with liquids on the unit.
Turn off the air conditioner at the power source when it will not be used for an extended period of time.
Periodically check the condition of the unit’s installation accessories for any damage.
Do not apply heavy pressure to the radiator fins of the unit.
Operate the unit with air filter in place.
Do not block or cover the intake grille, discharge area and outlet ports.
Ensure that any electrical/electronic equipment is one yard away from the unit.
Do not use or store flammable gases near the unit.
Do not touch the metal parts of the unit when removing the filter. Injuries can occur when handling sharp metal edges.
Do not use water to clean inside the air conditioner. Exposure to water can destroy the insulation, leading to possible electric shock.
When cleaning the unit, first make sure that the power and circuit breaker are turned off.
READ THIS SECTION BEFORE ATTEMPTING TO OPERATE AIR CONDITIONER.
Unit must be upright for one hour prior to operating.
The power supply cord contains a current device that senses damage to the power cord. To test
your power supply cord do the following:
Plug in the Air Conditioner.
The power supply cord will have TWO buttons on the plug head. Press the TEST button. You will
notice a click as the RESET button pops out.
Plug in &
Press the RESET button. Again you will notice a click as the button engages.
press RESET
The power supply cord is now supplying electricity to the unit. (This is also indicated by a light
on the plug head).
NOTE:
Do not use this device to turn the unit on or off.
Always make sure the RESET button is pushed in for correct operation.
The power supply cord must be replaced if it fails to reset when either the TEST button is pushed,
or it cannot be reset. A new one can be obtained from the product manufacturer.
If power supply cord is damaged, it CANNOT be repaired. It MUST be replaced by one obtained
from the product manufacturer.
2009 Electrolux Home Products, Inc.
All rights reserved.
Product Registration, Packaging & Normal Sounds
Record Your Model and Serial Numbers
Product Registration
Record in the space provided below the model and serial numbers. On all models, the
serial plate is located on the outside of the cabinet.
Model No.
Serial No.
Register Your Product
The self-addressed PRODUCT REGISTRATION CARD should be filled in completely,
signed and returned to the Frigidaire Company.
Remove all packaging from inside the carton, along with any
inserts placed into the side louvers.
Packaging
PACKAGING
INSERTS
Normal Sounds
High pitched Chatter
Today’s high efficiency compressors
may have a high pitched chatter
during the cooling cycle.
Vibration
Unit may vibrate and make noise
because of poor wall or window
construction or incorrect installation.
Sound of Rushing Air
At the front of the unit, you may
hear the sound of rushing air
being moved by the fan.
Pinging or Swishing
Droplets of water hitting condenser
during normal operation may cause
“pinging or swishing” sounds.
Note: Don’t try to drill any holes
on the base pan to eliminate the
normal sounds, otherwise it will
void the warranty.
Gurgle/Hiss
“Gurgling or hissing” noise may be heard
due to refrigerant passing through
evaporator during normal operation.
2009 Electrolux Home Products, Inc.
All rights reserved.
Air Conditioner Features & Operating Instructions
ELECTRONIC CONTROL
Before you begin, thoroughly familiarize yourself with the control panel and remote
as shown below and all its functions, then follow the symbol for the functions you
desire. The unit can be controlled by the touch pad alone or with the remote.
Air Conditioner Features
ADJUSTS
TEMPERATURE
OR TIME
DISPLAYS
TEMPERATURE/TIME
TURNS UNIT
ON OR OFF
SETS FAN SPEED
SETS MODE
REMOTE CONTROL
Battery Size: AAA
Warning: Do not mix old and new batteries. Do not
mix alkaline, standard (cabon-zinc), or rechargeable
(nickel-cadmium) batteries.
CHECK FILTER
RESET BUTTON
ACTIVATES
TlMER
Note: This remote control is a universal one for lots
of models. Some features on the remote control may
not be applicable to this model.
TOUCH PAD
Operating Instructions
NOTE
The following instructions represent the Touch Pad, the same instructions can be used for the Remote Control.
TO TURN UNIT ON: YOU WILL SEE:
DO THIS:
PRESS ON/
OFF BUTTON
Note: The unit will run in energy saver mode
when used for the first time. In this mode, the
fan will continue to run for 1 minute after the
compressor shuts off. The fan then cycles on
for 20 seconds at 10 minute intervals until the
room temperature is above the set temperature,
at which time the compressor turns back on.
2009 Electrolux Home Products, Inc.
All rights reserved.
Operating Instructions
Operating Instructions
(continued)
TO CHANGE TEMPERATURE
SETTlNG:
YOU WILL SEE:
Note: Tap or hold either up(
) or down(
)
button until the desired temperature is seen on the
display. This temperature will be automatically main-
tained anywhere between 60 °F (16 °C) and 90 °F
(32 °C). If you want the display to read the actual
room temperature. See "To Operate on Fan Only"
section on Page 7.
DO THIS:
PRESS TO
RAISE
PRESS TO
LOWER
TO ADJUST FAN SPEEDS:
YOU WILL SEE:
DO THIS:
PRESS TO
SELECT:
TO USE AUTO FAN FEATURE:
YOU WILL SEE:
Note: Fan starts at High Speed and adjusts to a
slower speed as the room temperature dictates. For
example, if the room doesn't get too warm, it will
stay at the slowest speed. If the room temperature
rises quickly, such as a door being opened, it will
automatically go to the highest speed. The fan
speeds will re-adjust back to the slowest speed as
the room returns to the original set temperature.
Press either the fan slower or fan faster button to
adjust the fan speed manually.
DO THIS:
PRESS FAN
BUTTON
CHOOSE AUTO
2009 Electrolux Home Products, Inc.
All rights reserved.
Operating Instructions
Operating Instructions
(continued)
TO OPERATE ON FAN ONLY:
YOU WILL SEE:
Note: Use this function only when cooling is not
desired, such as for room air circulation or to exhaust
stale air on some models. (Remember to open the vent
during this function, but keep it closed during cooling
for maximum cooling efficiency.) You can choose any
fan speed you prefer. (Except “Auto Fan”).
During this function, the display will show the actual
room temperature, not the set temperature as in
the cooling mode.
DO THIS:
PRESS MODE
BUTTON
CHOOSE FAN
ONLY
TO USE THE COOL FEATURE:
YOU WILL SEE:
Note: In this mode, the fan remains on all the time
with the compressor cycling on and off when room
temperature is reached.
DO THIS:
PRESS MODE
BUTTON
CHOOSE
COOL
TlMER: DELAY STOP / START
FEATURE:
YOU WILL SEE HOW MUCH TIME IS CHOSEN:
FIRST
Note: For Delay Stop, the unit must be in the On position.
Note: For Delay Start, the unit must be in the Off position.
To adjust timer setting, tap or hold the UP arrow ( ) or
the DOWN arrow ( ) to change delay timer at 0.5 hour
DO THIS:
PRESS
TIMER BUTTON
increments, up to 10 hours, then at 1 hour increments up
to 24 hours. The control will count down the time remain-
ing until start (8, 7.5, 7, etc.). The Delay Start mode auto-
matically selects cooling with maximum Fan Speed. The
temperature maintained will be the same as previously set.
To change the set temperature, press "COOL" then Up or
Down arrows until the desired temperature is indicated on
the display. After 5 seconds, the control will automatically
change the display back to the hours remaining until the
unit will start/stop. Turning the unit "ON" or "OFF" at any
time will cancel the Delay Start/Stop function.
THEN
DO THIS:
PRESS
UP/DOWN
SET BUTTONS
The Delay Start/Stop Feature will work until the unit either
starts or stops. Once that happens, the above steps have
to be repeated again.
2009 Electrolux Home Products, Inc.
All rights reserved.
Operating Instructions
Operating Instructions
(continued)
CHECK FILTER FEATURE, YOU WILL SEE:
Note: This feature is a reminder
to clean the Air Filter (See Care
and Cleaning) for more efficient
operation. The LED (light) will
illuminate after 250 hours of
operation. To reset after cleaning
the filter, press the "Filter Reset"
button and the light will go off.
DO THIS:
PRESS FILTER
RESET BUTTON
TO CHANGE TEMPERATURE DISPLAY:
YOU WILL SEE:
DO THIS:
PRESS AND HOLD
THE UP/DOWN
BUTTONS TOGETHER
FOR 3 SECONDS
Note: The control is capable of displaying temperature
in degrees Fahrenheit or degrees Celsius.
FAULT CODES
TO TURN UNlT OFF:
DO THIS:
PRESS ON/
OFF BUTTON
Note: If the unit is turned off in heat mode
(if applicable) or fan only mode, it will return
to the same setting when it is turned on again.
When the unit is turned off in cool or energy
saver mode, it will run in energy saver mode.
when it is turned on again, but the setting of
temperature and fan speed will remain.
If the display reads "AS" ,
a sensor has failed. Contact
your Authorized Frigidaire
Service Center.
2009 Electrolux Home Products, Inc.
All rights reserved.
8
Operating Instructions Care and Cleaning & Energy Saving Ideas
,
ADDITIONAL THINGS YOU SHOULD KNOW
Now that you have mastered the operating procedure, here are more features in your control that you should become familiar with.
The "Cool" circuit has an automatic 3 minute time delayed start if the unit is turned off and on quickly.
This prevents overheating of the compressor and possible circuit breaker tripping. The fan will continue
to run during this time.
There is a 2-Second delay for the compressor shutting down when selecting FAN ONLY. This is to cover the possibility of having
to roll through to select another mode.
The control will maintain the set temperature within 2 degrees Fahrenheit, between 60F and 90F degrees.
After a power outage, the unit will memorize the last setting and return the unit to the same setting once power is restored.
Air Directional Louvers
AUGER WHEELS
Air directional louvers control air flow direction. Your air conditioner has the louver
type described below.
Auger Type
The louvers will allow you to direct the air flow Up or Down and Left or Right
throughout the room as needed. Rotate the Auger Wheels until the desired
Left/Right direction is obtained. Pivot horizontal louvers until the desired
(8-WAY)
Up/Down direction is obtained.
Clean your air conditioner occasionally to keep it looking new. Be sure to unplug
the unit before cleaning to prevent shock or fire hazards.
Care and Cleaning
Air Filter Cleaning
The air filter should be checked at least once a month to see if cleaning is
necessary. Trapped particles in the filter can build up and cause an accumulation
of frost on the cooling coils.
Remove filter by sliding out from the right side.
Wash the filter using liquid dishwashing detergent and warm water. Rinse filter
thoroughly. Gently shake excess water from the filter. Be sure filter is
thoroughly dry before replacing.
Or instead of washing, you may vacuum the filter clean.
Cabinet Cleaning
Be sure to unplug the air conditioner to prevent shock or fire hazard. The
cabinet and front may be dusted with an oil-free cloth or washed with a cloth
dampened in a solution of warm water and mild liquid dishwashing detergent.
Rinse thoroughly and wipe dry.
Never use harsh cleaners, wax or polish on the cabinet front.
Be sure to wring excess water from the cloth before wiping around the controls.
Excess water in or around the controls may cause damage to the air conditioner.
Plug in air conditioner.
Winter Storage
If you plan to store the air conditioner during the winter, remove it carefully from
the window according to the installation instructions. Cover it with plastic or return
it to the original carton.
Do not block air flow inside with blinds, curtains or furniture; or outside with
Energy Saving Ideas
shrubs, enclosures, or other buildings.
The capacity of the room air conditioner must fit the room size for efficient and
satisfactory operation.
Install the room air conditioner on the shady side of your home. A window that faces
north is best because it is shaded most of the day.
Close the fireplace damper, floor and wall registers so cool air does not escape up
the chimney and into the duct work.
Keep blinds and drapes in other windows closed during the sunniest part of the day.
Clean the air filter as recommended in the section “Care and Cleaning”.
Proper insulation and weather stripping in your home will help keep warm air out
and cool air in.
External house shading with trees, plants or awnings will help reduce the air
conditioner’s work load.
Operate heat producing appliances such as ranges, washers, dryers and dishwashers
during the coolest part of the day.
2009 Electrolux Home Products, Inc.
All rights reserved.
Before You Call
Before calling for service, review this list. It may save you time and expense. This list includes common occurrences that are not
the result of defective workmanship or materials in this appliance.
OCCURRENCE
SOLUTION
Air conditioner will not operate.
Wall plug disconnected. Push plug firmly into wall outlet.
Plug Current Device Tripped. Press the RESET button.
House fuse blown or circuit breaker tripped. Replace fuse with time delay type or reset circuit breaker.
Control is OFF. Turn Control ON and set to desired setting.
Room temperature below 60°F (16°C). Cooling may not occur until room temperature rises above
60°F (16°C).
Air from unit does not feel cold
enough.
Temperature sensing element touching cold coil, located behind air filter. Straighten away from coil.
Reset to a lower temperature.
Compressor shut-off by changing modes. Wait approximately 3 minutes and listen for compressor to
restart when set in the COOL mode.
Air conditioner cooling, but room
is too warm - ice forming
on cooling coil behind decorative
front
Outdoor temperature below 60 O F (16 OC). To defrost the coil, set FAN ONLY mode.
Air filter may be dirty. Clean filter. Refer to Care and Cleaning section. To defrost, set to FAN ONLY
mode.
Temperature is set too Low for night-time cooling. To defrost the coil, set to FAN ONLY mode. Then,
set temperature to a higher setting.
Dirty air filter - air restricted. Clean air filter. Refer to Care and Cleaning section.
Temperature is set too high. Set temperature to a lower setting.
Air conditioner cooling, but room
is too warm - NO ice forming on
cooling coil behind decorative
front.
Air directional louvers positioned improperly. Position louvers for better air distribution.
Front of unit is blocked by drapes, blinds, furniture, etc. - restricts air distribution. Clear blockage in
front of unit.
Doors, windows, registers, etc. open - cool air escapes. Close doors, windows, registers, etc.
Unit recently turned on in hot room. Allow additional time to remove “stored heat” from walls, ceiling,
floor and furniture.
Dirty air filter - air restricted. Clean air filter.
Air conditioner turns on and off
rapidly.
Outside temperature extremely hot. Set FAN speed to a faster setting to bring air through cooling coils
more frequently.
Noise when unit is cooling.
Air movement sound. This is normal. If too loud, set to lower FAN setting.
Window vibration - poor installation. Refer to installation instructions or check with installer.
Improper installation. Tilt air conditioner slightly to the outside to allow water drainage. Refer to
installation instructions or check with installer.
Water dripping INSIDE when
unit is cooling.
Water dripping OUTSIDE when
unit is cooling.
Unit removing large quantity of moisture from humid room. This is normal during excessively humid
days.
Room too cold.
Set temperature too low. lncrease set temperature.
If These Solutions Fail, Call 1-800-944-9044 For Frigidaire Service.
2009 Electrolux Home Products, Inc.
All rights reserved.
Major Appliance Limited Warranty
Your appliance is covered by a limited two-year warranty and a limited 3-5 year warranty on the sealed system (the compressor,
condenser, evaporator and tubing). For two years from your original date of purchase, Electrolux will pay all costs for repairing or
replacing any parts of this appliance that prove to be defective in materials or workmanship when such appliance is installed,
used and maintained in accordance with the provided instructions. From the third to the fifth year from your original purchase
date, Electrolux will repair or replace any parts in the Sealed Refrigeration System (compressor, condenser, evaporator and tubing)
that prove to be defective in materials or workmanship. In years 3-5, the consumer will be responsible for diagnostic, labor and
parts costs as well as any removal, transportation and reinstallation expenses which are incurred during service on components
other than those covered under the Sealed Refrigeration System 5-year warranty.
Exclusions
This warranty does not cover the following:
1. Products with original serial numbers that have been removed, altered or cannot be readily determined.
2. Product that has been transferred from its original owner to another party or removed outside the USA or
Canada.
3. Rust on the interior or exterior of the unit.
4. Products purchased "as-is" are not covered by this warranty.
5. Food loss due to any refrigerator or freezer failures.
6. Products used in a commercial setting.
7. Service calls which do not involve malfunction or defects in materials or workmanship, or for appliances not
in ordinary household use or used other than in accordance with the provided instructions.
8. Service calls to correct the installation of your appliance or to instruct you how to use your appliance.
9. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves,
etc., which are not a part of the appliance when it is shipped from the factory.
10. Service calls to repair or replace appliance light bulbs, air filters, water filters, other consumables, or knobs,
handles, or other cosmetic parts.
11. Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry trip
charges, or mileage expense for service calls to remote areas, including the state of Alaska.
12. Damages to the finish of appliance or home incurred during installation, including but not limited to floors,
cabinets, walls, etc.
13. Damages caused by: services performed by unauthorized service companies; use of parts other than
genuine Electrolux parts or parts obtained from persons other than authorized service companies; or external
causes such as abuse, misuse, inadequate power supply, accidents, fires, or acts of God.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR OR
REPLACEMENT AS PROVIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES, INCLUDING WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST
PERIOD ALLOWED BY LAW, BUT NOT LESS THAN ONE YEAR. ELECTROLUX SHALL NOT BE LIABLE FOR
CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES
RESULTING FROM ANY BREACH OF THIS WRITTEN LIMITED WARRANTY OR ANY IMPLIED WARRANTY. SOME
STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSE-
QUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES, SO THESE LIMITATIONS
OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WRITTEN WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS.
YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.
If You Need Keep your receipt, delivery slip, or some other appropriate payment record to establish the warranty period
Service
should service be required. If service is performed, it is in your best interest to obtain and keep all receipts.
Service under this warranty must be obtained by contacting Electrolux at the addresses or phone
numbers below.
This limited warranty only applies in the USA and Canada. In the USA, your appliance is warranted by Electrolux Major Appliances
North America, a division of Electrolux Home Products, Inc. In Canada, your appliance is warranted by Electrolux Canada Corp.
Electrolux authorizes no person to change or add to any obligations under this warranty. Obligations for service and parts under
this warranty must be performed by Electrolux or an authorized service company. Product features or specifications as described
or illustrated are subject to change without notice.
USA
Canada
1.800.265.8352
Electrolux Canada Corp.
5855 Terry Fox Way
Mississauga, Ontario, Canada
L5V 3E4
1.800.944.9044
Electrolux Major Appliances
10200 David Taylor Drive
Charlotte, NC 28262
2009 Electrolux Home Products, Inc.
All rights reserved.
|