STEAM MOP
OWNER’S MANUAL
Model S3305H
120V., 60Hz., 800 Watts
For information or assistance:
EURO-PRO Operating LLC
94 Main Mill Street, Door 16
Plattsburgh, NY 12901
Tel.: 1 (800) 798-7398
Model S3305H
IMPORTANT SAFETY INSTRUCTIONS
1 YEAR LIMITED WARRANTY
When using your Steam Mop, basic safety precautions should always be
observed, including the following:
Your Steam Mop is warranted to be free from defects in material and workmanship for a
period of one (1) year from the date of purchase when utilized for normal household use
by the original purchaser only. The included Warranty Registration Card must be filled out
and returned within 10 days of purchase. This is essential for your Warranty to be
effective should any problem arise with this product.
Should any defect covered by the terms of the limited warranty be discovered within one
year, EURO-PRO Operating LLC will repair or replace any defective part provided the
unit is returned by the original purchaser, freight prepaid, to:
14. Do not put any objects into
openings. Do not use with any
opening blocked.
15. Do not put hands or feet under the
Steam Mop. Unit gets very hot.
16. Use ONLY on Flat, horizontal
surfaces. Do not use on walls,
counters or windows.
17. Do not add cleaning solutions,
scented perfumes, oils or any other
chemicals to the water used in this
appliance as this may damage the
unit or make it unsafe for use. Use
regular tap water or distilled/purified
water if the tap water in your area is
very hard.
18. When in use, never turn the
appliance over or on its side.
NEVER DIRECT STEAM
TOWARDS PEOPLE, ANIMALS
OR PLANTS.
19. Do not handle the micro-fiber
cleaning cloth immediately after
turning the unit off. Place the
appliance on the floor pad to cool
down before removing.
20. NEVER LEAVE THE APPLIANCE
IN ONE SPOT ON ANY SURFACE
FOR ANY PERIOD OF TIME.
ALWAYS PLACE ON THE FLOOR
PAD AND MAKE SURE THAT THE
APPLIANCE IS TURNED OFF.
21. When cleaning the Steam Mop, turn
the appliance off and clean with a
dry or damp cloth. Do not pour
water or use alcohol, benzene or
thinner.
22. Extreme caution should be
exercised when using this appliance
to clean stairs.
23. Never use Steam Mop without
micro-fiber cleaning cloth or bonnet
(optional) attached.
1. Read all instructions before using your
steam mop.
2. Use the system only for its intended
use.
3. Do not use outdoors.
4. Do not leave the Steam Mop
unattended when plugged in. Turn the
unit off and unplug the electrical cord
from the outlet when not in use and
before servicing.
5. Do not allow to be used as a toy. Close
attention is necessary when used by or
near children, pets or plants. Do not
leave appliance unattended while
connected.
EURO-PRO Operating LLC, 94 Main Mill Street, Door 16, Plattsburgh, N.Y., 12901
Proof of purchase date and $12.95 for handling and return packing/shipping charges must
be included.*
The liability of under this warranty is limited solely to the cost of the replacement parts or
the complete unit at our option. LABOUR CHARGES ARE NOT INCLUDED.
This warranty does not cover normal wear of parts and does not apply to any unit that has
been tampered with or used for commercial purposes. This Limited Warranty does not
cover damage caused by misuse, negligent handling, or damage due to faulty packaging
or mishandling in transit (by any common carrier).
This warranty is extended to the original purchaser of the unit and excludes all other legal
and/or conventional warranties. The responsibility of EURO-PRO Operating LLC , if any,
is limited to the specific obligations expressly assumed by it under the terms of the limited
warranty. In no event is EURO-PRO Operating LLC liable for incidental or consequential
damages of any nature whatsoever. Some States/Provinces do not permit the exclusion
or limitation of incidental or consequential damages, so the above may not apply to you.
6. Use only as described in this manual.
7. Use only manufacturer’s recommended
accessories.
8. Do not operate the appliance with a
damaged plug or cord, or if the unit has
been dropped or damaged. To avoid
the risk of electric shock, do not
disassemble or attempt to repair the
appliance on your own. Return the
Steam Mop to EURO-PRO Operating
LLC (see warranty) for examination and
repair. Incorrect re-assembly or repair
can cause a risk of electrical shock or
injury to persons when the Steam Mop
is used.
9. To protect against a risk of electric
shock, do not immerse the Steam Mop
into water or any other liquids.
10. Do not pull or carry by power cord, use
cord as handle, close a door on cord, or
pull cord around sharp edges or
corners. Keep cord away from heated
surfaces.
This warranty gives you specific legal rights which vary from state to state or province to
province.
*Important: Carefully pack item to avoid damage in shipping. Be sure to attach tag to item
before packing with your name, complete address and phone number with note giving
purchase information, model number and what you believe is the problem with item. We
recommend you insure the package (as damage in shipping is not covered by your
warranty). Mark the outside of your package “ATTENTION CUSTOMER SERVICE”. We
are constantly striving to improve our products, therefore the specifications
contained herein are subject to change without notice.
yyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyy
OWNERSHIP REGISTRATION CARD
Please fill out and mail the product registration card within ten (10) days of purchase. The
registration will enable us to contact you in the unlikely event of a product safety notification. By
returning this card you acknowledge to have read and understood the instructions for use, and
warnings set forth in the accompanying instructions.
11. do not unplug by pulling on power cord.
To unplug, grasp the plug not the cord.
Do not use extension cords or outlets
with inadequate current carrying
capacity.
EURO-PRO Operating LLC, 94 Main Mill Street, Door 16, Plattsburgh, N.Y. 12901
Model S3305H
______________________________________________________________________
24. Keep your work area well lit.
25. Store Steam Mop indoors in a cool,
dry place.
12. Turn the unit off before unplugging from
electrical outlet.
13. Do not handle plug or Steam Mop
with wet hands or operate appliance
without shoes.
Appliance model
______________________________________________________________________
Date purchased
Name of store
______________________________________________________________________
Owner's name
______________________________________________________________________
SAVE THESE INSTRUCTIONS
Address
City
State
Zip Code
For Household Use Only
8
Rev. 07/03D
Printed in Korea
1
TROUBLE SHOOTING
ADDITIONAL IMPORTANT SAFEGUARDS
1. To avoid circuit overload, do not operate another appliance on the same electrical
outlet (circuit)
PROBLEM
POSSIBLE CAUSE
POSSIBLE SOLUTION
1. Plug unit in firmly.
2. Check fuse or breaker.
Replace fuse/reset
breaker.
2. If an extension cord is absolutely necessary, a 15 ampere 14 gage cord should be
used. Cords rated for less amperage may overheat. Care should be taken to
arrange cord so that it cannot be pulled or tripped over.
3. Do not leave unattended when the system is connected to a power
supply/electrical outlet.
1. Power cord not firmly
plugged into outlet.
2. No power in wall outlet.
3. Needs servicing.
STEAM MOP WILL
NOT OPERATE
3. Call 1-800-798-7398.
1. Add water to the water
tank following instructions
on page 5.
STEAM MOP WILL
NOT MAKE STEAM
1. No water in water tank.
SAVE THESE INSTRUCTIONS
1. Turn off unit, unplug from
power outlet and change
the micro-fiber cleaning
cloth or bonnet
1. Micro-fiber cleaning cloth
is too wet.
FOR HOUSEHOLD USE ONLY
STEAM MOP
LEAVES WATER
ON THE FLOOR
2. Unit is not level on the
floor.
(optional).
2. Always keep the steam
mop level and parallel to
the floor.
WARNING: This appliance is equipped with a
grounded-type 3-wire cord (3-prong
plug). This plug will only fit into an
electrical outlet made for a 3-prong
plug. This is a safety feature. If the
plug should fail to fit the outlet, contact
an electrician to replace the outlet. Do
not attempt to defeat the safety purpose
of the grounding pin, part of the
1. Always place the steam
mop on the floor
protector pad when not in
use. To remove, use a
damp, dry cloth with a
few drops of white
1. Steam mop left in one
spot too long.
STEAM MOP LEFT
WHITE SPOT ON
FLOOR
2. Steam mop not rested on
floor protector pad.
vinegar and rub the stain
to remove.
3. Hard water.
2. Always place the steam
mop on the floor
protector pad when not in
use.
3. Use distilled water.
3-prong plug.
FOR TECHNICAL SUPPORT
for Model S3305H
Call.: 800-798-7398
Monday to Friday 8:30 A.M. - 5:00 P.M. Eastern Standard Time
2
7
OPERATING INSTRUCTIONS
GETTING TO KNOW YOUR STEAM MOP
Care & Maintenance
Helpful Hints
1. Always vacuum or sweep before
steam cleaning.
IMPORTANT: Always insure that the
unit is “UNPLUGGED” from the wall
receptacle prior cleaning or before
emptying the water tank.
2. The easiest way to use the
machine is to tilt the ergonomic
handle to a 45° angle and clean
slowly 2-3 yards at a time.
3. Hand wash or machine wash the
micro-fiber cleaning cloths or
bonnet (optional) in a delicate cycle
with a mild detergent.
4. We recommend air drying the
micro-fiber cleaning cloths or
bonnet (optional) for 24 hours, but
they could be dried in a dryer on a
low heat setting.
5. A good amount of steam passes
through the micro-fiber cleaning
cloth. We recommend that the
cleaning cloth be changed when it
gets too wet. These need to be
replaced as necessary.
1. Turn the unit off and unplug from
electrical outlet.
2. Wrap power cord around cord
holders.
3. Let the unit cool for five (5) minutes
before removing the micro-fiber
cleaning cloth or bonnet (optional)
and before emptying the water tank.
4. Always empty the water tank when
you have finished using the unit.
5. Never leave the micro-fiber cleaning
cloth or bonnet (optional) on the unit
when you have finished using the
steam mop. Always remove the
micro-fiber cleaning cloth or bonnet
(optional) and wash in warm water
with a mild detergent. Never use
bleach or fabric softener when
cleaning the micro-fiber cleaning
cloth. The micro-fiber cleaning cloth
or bonnet (optional) can be washed
in a washing machine and dried in a
clothes dryer but on low heat. We
recommend that you air dry for 24
hours but it could also be dried in a
clothes dryer on a low heat setting.
6. Wipe the unit with a damp cloth to
clean. Never immerse main unit in
water or any other liquid.
6. To remove stubborn stains from
vinyl or linoleum floors, pre-treat
with a mild detergent and some
water before using the steam mop.
IMPORTANT:
Never leave the steam mop in one
spot for any period of time. Always
place the appliance on the floor
protector pad and make sure that
the appliance is turned off.
7. In order to keep your steam mop in
good condition, we recommend that
you clean the water tank once a
month to eliminate calcium deposits.
Add three ounces (3 oz) of water to
the water tank and shake to loosen
any deposits. Remove the filling cap
and immediately empty water into a
sink. Do not use vinegar or other
decalcifying substances in the
steam mop water tank.
9. Tube Pivot
10. Cord Holder
1. Hand Grip
2. Power Cord
3. 2-Piece Ergonomic Handle
4. Filling Cap
5. Main Unit
6. On/Off Button
7. Power “On” Light (Green)
8. Empty Light (Red)
11. Micro-Fiber Cleaning Cloth (x2)
12. Floor Bonnet (Optional)
13. Filling Flask
14. Floor Protector Pad
15. Handle Joint
Caution: Do not immerse the unit in
water or any other liquids.
Technical Specifications
Voltage:
Power:
Water Capacity:
120V., 60Hz.
800 Watts
8 U.S. Fl. Oz.(250ml)
Note: Illustrations may differ from actual unit.
6
3
FEATURES
OPERATING INSTRUCTIONS
Your Steam Mop utilizes steam to remove tough grease,dirt and grime. Steam is
nature’s purest and most powerful cleaner for safely cleaning all hard floor surfaces in
your home without harsh chemicals, thus being perfectly ecological. Cleans your tile,
hardwood , linoleum and vinyl floors.
How To Assemble & Use
6. Plug the unit into a standard 120 volt
grounded wall receptacle.
IMPORTANT: Always insure that the
unit is “UNPLUGGED” from the wall
receptacle prior to initial filling and before
attaching the micro-fiber cleaning cloth to
the base of the appliance. Never use the
steam mop without the micro-fiber
cleaning cloth or bonnet (optional)
attached to the base.
7. Press the On/Off button to turn the
unit on. The power ‘On” light will light
up. It takes the unit approximately
two - three (2-3) minutes to heat up.
8. When there is no more water in the
water tank, the empty light (red) will
go on.
9. To refill the water tank, turn the unit
off and unplug from the electrical wall
outlet and let the unit cool for 30
seconds. Then remove the filling cap
and pour in the water. You do not
have to wait for the unit to cool down
before you refill.
10.When you have finished using the
steam mop, turn the unit “Off” and
wait until the steam mop cools down
for approximately five (5) minutes
before removing the micro-fiber
cleaning cloth or bonnet (optional)
from the base. Please note that the
micro-fiber cleaning cloth or bonnet
(optional) gets very hot with the
steam.
11.Never leave the micro-fiber cleaning
cloth or bonnet (optional) on the unit
when you have finished using the
steam mop. Always remove the
micro-fiber cleaning cloth or bonnet
(optional) and wash in warm water
with a mild detergent. Never use
bleach or fabric softener when
cleaning the micro-fiber cleaning
cloths or bonnet (optional). The
micro-fiber cleaning cloth or bonnet
(optional) can be washed in a
washing machine and dried in a
clothes dryer but on a low heat
setting. We recommend that you air
dry for 24 hours.
WARNING: Your Steam Mop is designed to clean hard floor surfaces that
will withstand high heat. Do not use on unsealed wood or
unglazed ceramic floors. On surfaces that have been treated
with wax or some no wax floors, the sheen may be removed by
the heat and steam action. It is always recommended to test an
isolated area of the surface to be cleaned before proceeding.
We also recommend that you check the use and care
Always let unit cool for at least 5 minutes
before removing the micro-fiber cleaning
cloth or before emptying the water tank.
1. Remove all the parts from the
packaging.
instructions from the floor manufacturer.
2. Insert the ergonomic handle into the
tube pivot of the main unit.
IMPORTANT: Never leave the appliance in one spot on any surface
for any period of time. Always place the appliance on the
floor protector pad and make sure that the appliance is
turned off.
3. Place one of the micro fiber cleaning
cloths or bonnet (optional) on the
bottom of the steam mop. Make sure
that the micro-fiber cleaning cloth or
bonnet (optional) is firmly attached to
the bottom of the steam mop. (Fig. 1)
4. Place the steam mop on the floor
protector pad and open the filling
cap.
5. With the help of the filling flask, pour
1 cup of water (8 oz.) Into the unit. do
not overfill.. Replace filling cap when
finished. (Fig. 2)
CAUTION: Use a grounded receptacle. Use only a heavy duty extension
cord rated for 15 amps minimum - Do not use an ordinary
extension cord.
IMPORTANT: Do NOT add cleaning solutions, scented perfumes, oils or
any other chemicals to the water used in this appliance.
Use regular water or distilled/purified water if the tap
water in your area is very hard.
Fig. 1
WARNING: Colors may bleed
during first wash. Be careful when
machine washing or drying with
mixed fabrics as micro-fiber cloths
will pick up lint from other fabrics.
Fig. 2
Using The Micro-Fiber
Bonnet (Optional)
If you wish to use the micro-fiber bonnet
(optional), follow same instructions as
above, except that you slip the bonnet
(optional) over the main unit.
4
5
|